The Tool Desk
Outbyte Driver Updater FREEFix the driver behind crashes, sound loss and screen glitchesFind Drivers →Outbyte PC Repair FREEClear out junk files and repair common Windows errorsFree Scan →For a safer rip cut, prepare the saw with the correct blade and working safety devices, install its through-cut guard assembly as the manual directs, lock the rip fence parallel to the blade, and plan support for both the board and offcut. Keep hands clear of the cut line, stand to the side of the blade, and use a push stick when the work or feed position calls for one. Never operate a saw with a defective safety device.
Inspect the saw before setting up
With the saw switched off, inspect the blade, rip fence, guard, riving knife or spreader, and anti-kickback devices. Use a blade suitable for ripping, and remove any cracked or damaged blade from service. Do not operate the saw if a guard or other safety device is defective. OSHA identifies blade condition and setup among factors related to kickback (OSHA table-saw guidance; OSHA kickback guidance).
Fit the safeguards for a through-cut
A rip cut that passes through the stock is a through-cut. Use the blade guard, riving knife or spreader, and anti-kickback device where the saw design provides them, and configure them as the manufacturer specifies. For example, Bosch’s GTS1510 safety instructions call for the blade guard, riving knife, and anti-kickback device for every through-cutting operation, with the riving knife adjusted as described in that manual. That configuration is specific to the model; follow the manual for your saw rather than assuming parts or adjustments are interchangeable (Bosch GTS1510 safety instructions; OSHA table-saw guidance).
Set and check the rip fence
- With the saw off, position the rip fence for the desired cut width.
- Lock the fence and check that it is secure before starting.
- Feed the workpiece parallel to the fence so it is guided parallel to the blade. OSHA says this minimizes the potential for kickback (OSHA table-saw guidance).
Use the rip fence—not the rip fence and miter gauge together—to guide the same workpiece during a rip cut. Bosch warns that using both at once increases the likelihood of blade binding and kickback (Bosch GTS1510 safety instructions).
Outdated Drivers Are Slowing You Down
One free scan finds every outdated or missing driver and matches the right update for your exact hardware.Free scan · exact hardware matchWindows Errors? Fix Them Before They Spread
Repair common Windows errors and clear accumulated junk for a smoother, more stable PC - no reinstall needed.Free scan · no reinstall#1 Best Overall
- PRECISION TABLE SAW RIP FENCE UPGRADE : Built from high-strength extruded aluminum, this table saw rip fence extension provides a stable, straight reference surface for cleaner and more consistent cuts. The rigid profile helps reduce flex and supports accurate alignment during repeated table saw operations
- 46" EXTENDED SUPPORT WITH SPACE-SAVING DESIGN : This 46" table saw fence extension kit with featherboards measures 47-1/4" overall and adds support when working with long boards or sheet goods. It functions as a table saw extension and outfeed support without requiring a bulky outfeed table
- VERSATILE 3-IN-1 MULTI-FUNCTION FENCE SYSTEM : Configure the fence for different cutting tasks: High Fence Mode supports tall panels and box work, Low Fence Mode 3/4" helps with controlled thin ripping, and L-Fence Mode supports edge jointing or template-guided cuts. It also works as a thin rip jig and table saw jig for added workshop flexibility
- 8 BUILT-IN T-SLOTS FOR CUSTOM JIG SETUPS: The fence body features eight integrated T-slots for mounting featherboards, stop blocks, hold-downs, and custom woodworking jigs. The included drop-in T-bolts can be inserted directly through the slot opening, allowing faster setup and adjustment without sliding hardware in from the ends of the track
- FITS MOST TABLE SAW FENCES WITH 1-1/4" OFFSET ALIGNMENT :Designed to clamp securely to most table saw rip fences without drilling or permanent modification. The 1-1/4" total thickness provides a clear offset reference
Plan support, stance, and hand position
- Make sure the stock has enough support as it enters and leaves the blade, and plan for the cut end and offcut so neither can snag or fall into the cutting area.
- Keep your hands out of the cut line. Stand to the side of the blade to reduce exposure if kickback occurs.
- Do not feed damaged or unstable stock.
Ripping carries kickback risk; OSHA describes kickbacks as more likely during ripping than crosscutting (OSHA table-saw guidance).
Use a push stick when needed
Keep a push stick within reach before starting. OSHA recommends using one for small pieces and to push stock past the blade. Choose a feeding method that keeps your hands away from the blade; a push stick supplements the guard and other safeguards rather than replacing them (OSHA table-saw guidance).
Rank #2
- One piece square tubular rail. Max Rip to Left of Blade-13-1/2 inch, Max Rip to right of Blade- 30 inch. Length: Fence 37 inch, Rail 57-1/2 inch. Height of the Fence is 2-1/2"
- Mounting design attaches to Delta table saws. This includes fence, steel guide tub with scale, front support rail One, rear support rail One and mounting hardware
- Three-point locking system with twin hairline pointers to assure fence is parallel to blade and accurate to within 1/64 of an inch (0. 4mm)
- Easy-gliding, steel tube fence body to handle Quick, precision ripping, and square cuts
- Fence securely clamps to front tube and hooks over rear rail to allow for fence attachments
Follow the saw manual for model-specific settings
Use the blade setup and operating instructions specified by the manufacturer. There is no single blade-height setting established here for every saw and blade, so consult your own manual instead of applying a universal measurement. OSHA’s guidance is written for U.S. workplace safety; requirements may differ elsewhere. For replacement guards, riving knives or spreaders, and anti-kickback devices, verify compatibility with the exact saw model and intended operation in its manual.
Quick Recap
Rank #4
- Compatible with major 10" table saw brands; fits specific models requiring rip fence replacement. This part is compatible with the following:RTS10G, RTS10NS
- Direct replacement for part #089040002702; rip fence; fits major brand compatible 10" table saws as an OEM-style substitute.
- Major brand-compatible design; durable rip fence; precise workpiece guidance; ensures straight and accurate cuts; easy user-friendly installation; essential for table saw operation; restores cutting accuracy.
- Replaces damaged, bent, or missing rip fence; fixes poor cut accuracy, workpiece wandering, or misalignment; eliminates cutting errors and wasted material; restores proper workpiece guidance for straight and accurate cuts; avoids costly saw replacement or professional repair.
- Premium rip fence—durable build, exact compatibility with major 10" table saws, and reliable performance; shop with confidence for reliable tool parts; trusted replacement for hassle-free saw maintenance.
Rank #3
- Accurate Cutting: Upgrade your rip guide precision with the Wixey digital rip saw fence system that offers ±0.002" accuracy per ft and a digital readout for reliable, repeatable cuts across all woodworking projects
- Heavy-Duty Build: Crafted from durable steel and aluminum, this professional-grade table fence delivers long-lasting stability and is perfect for woodworking benches, rip cuts, and shop work tables
- Digital Readout: Features a backlit digital display showing readings in inches, fractions, or millimeters; constant memory preserves calibration even when powered off or removed from the bench rail
- Smooth Adjustment: Micro-adjust wheels and roller glide ensure fine-tuned, smooth fence movement - ideal for setting precise bevels, rip cuts, and repeat measurements on contractor or cabinet saws
- What’s Included: You get (1) Wixey Table Saw Fence System (WR750) - (1) Digital Readout Display – (1) 72” Fence Rail (ships in two parts) - (1) Drilling Jig & Bit - Mounting Hardware Included - Batteries (2×AAA, not included) with this digital fence tool
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
Do these 3 things before closing this tab:
1Repair Windows errors before they cause bigger problems2Scan for outdated or missing drivers - takes under a minute3Clear out junk files and repair common Windows errors
