A documented SawStop auxiliary-fence build uses two 24-inch pieces—3/4-inch hardwood and 1/2-inch plywood—joined with wood glue and countersunk screws. In the SawStop manual’s setup, the plywood lies flat on the table while the hardwood bears against and is clamped to the rip fence. Those dimensions and placements are specific to that example; check your saw’s manual and confirm fit, alignment, clearance, and secure clamping before cutting.
Materials and dimensions in the SawStop example
The SawStop 10-inch Professional Cabinet Saw manual provides one auxiliary-fence construction example. It calls for:
- Piece A: 24 inches long, 3/4-inch-thick hardwood.
- Piece B: 24 inches long, 1/2-inch plywood.
- Fasteners: wood glue and countersunk wood screws.
- Clamping: clamps to secure the completed assembly to the rip fence during installation.
These are the manual’s specifications, not universal dimensions for other saws or fences. See the SawStop 10-inch Professional Cabinet Saw manual for its illustrated construction and setup.
How to build the fence
- Cut the hardwood and plywood to the lengths specified for the SawStop example, checking your own saw’s manual and the intended operation before using those dimensions.
- Position piece A along the edge of piece B, as shown in the SawStop manual.
- Join the pieces with wood glue and countersunk wood screws. Keep the assembly rigid and ensure the fasteners will not interfere with the saw, workpiece, or intended cut.
- Allow the glue to cure according to its instructions before fitting the fence to the saw.
How to fit it to your rip fence
In the SawStop illustration, piece B rests flat on the saw table and piece A bears against the left side of the rip fence. The manual places the front edge of piece B 1–2 inches behind the table’s front edge and instructs the user to clamp piece A securely to the rip fence. This position and orientation describe that SawStop setup only.
The Tool Desk
Outbyte Driver Updater FREEFix the driver behind crashes, sound loss and screen glitchesFind Drivers →Outbyte PC Repair FREEClear out junk files and repair common Windows errorsFree Scan →#1 Best Overall
- SPECS - ARF-BSCS | 36 Inch Table Saw Fence | 3-1/2" Tall | Built In T-Track Slots | 7" Material Support | 2 Sliding Clamping Blocks | Fence & Clamping Block Thickness Measure Exactly 2" | Made in USA
- SIZED FOR COMPACT MACHINES - 36" fence length, ideal for job site table saws, band saws, vintage contractor’s saws, router tables, and more.
- QUICK SETUP & REMOVAL - Installs in seconds without modifying your existing fence. Just use standard track clamps (not included).
- ENHANCED SUPPORT - Includes two 7" material supports to stabilize workpieces on the infeed and outfeed side of the blade.
- AMERICAN MADE QUALITY - Like all Woodpeckers products, the Compact Auxiliary Rip Fence is precisely built and carefully inspected in our Strongsville, Ohio facility.
Before cutting, consult the manual for your saw and verify that the auxiliary fence sits flat and securely, does not shift, and stays aligned with the rip fence. Check that it clears the blade and the saw’s guard, spreader or riving knife, and anti-kickback features for the operation. A fence that cannot be attached securely or that obstructs required safety equipment is not ready to use.
Use it without compromising saw safety
An auxiliary fence can provide a reference face or support for a particular operation; it does not prevent kickback and does not replace the saw’s guard, spreader or riving knife, or anti-kickback devices. OSHA explains that kickback can happen when the blade catches stock and throws it toward the operator. Its guidance recommends using a spreader to help prevent stock from squeezing the saw, anti-kickback fingers, a blade suitable for the cut, and stock guided parallel to the rip fence. Stand to the side of the blade, support stock, and wear eye and face protection. Read OSHA’s table-saw guidance.
Rank #2
- SPECS - ARF-48 | 48 Inch Table Saw Fence | 3-1/2" Tall | Built In T-Track Slots | 12" Material Support | 3 Sliding Clamping Blocks | Fence & Clamping Block Thickness Measure Exactly 2" | Made in USA
- STRAIGHTER, SMOOTHER CUTS - Clamp the Auxiliary Rip Fence to any table saw fence for a longer, straighter, and more precise reference surface - no twisting or warping like plywood fence faces.
- MORE CONTROL FOR BIG PROJECTS - The 48" length and 12" material support keep panels balanced and stable on the infeed or outfeed side of the blade for safer, cleaner cuts.
- VERSATILE SETUP OPTIONS - Configure high, low, or L-fence positions to match the task - from thin rips to box lids to edge jointing straight stock.
- MADE IN THE USA - Built and inspected to our strict standards in Strongsville, Ohio, ensuring top-tier accuracy and durability.
- Keep the applicable guard, spreader or riving knife, and anti-kickback features in the configuration required by the saw maker and the operation.
- Check that the rip fence is locked before starting. Use stock that is suitable for the cut; bowed or crooked stock can shift and contribute to kickback.
- Guide the workpiece parallel to the rip fence, and arrange suitable infeed and outfeed support for the stock and offcuts.
- Use a push device when the procedure calls for it. The SawStop manual says to move the workpiece along piece B and use the push block to finish when a hand comes within 6 inches of the blade. Oregon State University’s training specifies a push stick when ripping stock narrower than 5 inches. Follow the procedure for your saw and shop rather than treating either measurement as a universal rule.
- If a cut cannot be completed, stop and wait for the blade to stop before removing stock, as directed by Oregon State University’s table-saw training.
Check requirements for your saw and workplace
Table dimensions, rip-fence geometry, guards, and cutting operations differ. The SawStop example does not establish a fit or safe clearance for another saw, and the available sources do not establish a tested performance benefit for this design. Do not assume its measurements will work unchanged on your machine.
For workplace machinery, OSHA’s 29 CFR § 1910.213 includes requirements for hand-fed circular ripsaws, including a hood above the table and workpiece, a spreader, and nonkickback fingers. It also addresses fences secured without changing alignment with the saw. This workplace standard is not a substitute for checking your saw maker’s instructions and applicable local rules, and adding a wooden auxiliary fence does not discharge those requirements.
Free tools Windows power users keep installed
One-click scans. No signup required.
Quick Recap
Best Value
- FEED CONTROL AND SAFETY: The XT XTENDER T Track Fence adds a 5” tall face to improve workpiece guidance on table saws and bandsaws. The increased surface helps stabilize material, supporting straighter cuts and controlled feeding.
- MULTI-SAW FIT: This 46” XTENDER clamps to existing fences using Bow T-Track clamps (sold separately). Fits portable saws, cabinet saws, UniSaw, Harvey, and bandsaws—a choice among woodworking gifts for dad to upgrade his existing fence.
- MULTIPLE T-SLOTS FOR ACCESSORIES: Features three T-slots on the face, top, and back for 1/4” and 5/16” T-bolts. Our table saw fence system supports featherboards, stops, and feed accessories for customizable setups and improved control.
- HEAVY-DUTY ALUMINUM CONSTRUCTION: Built from aluminum extrusion with sandblasted anodized finish. The 4” flat face supports smooth material glide, while rigid 1” width maintains stability and alignment during woodworking operations.
- ADJUSTABLE POSITIONING AND EXTENSION SUPPORT: With milled rear slots, our table saw fence allows quick repositioning for infeed, center, or outfeed use. Standoffs help smooth movement, while accessory compatibility extends support for longer boards.
Rank #4
- Accurate Cutting: Upgrade your rip guide precision with the Wixey digital rip saw fence system that offers ±0.002" accuracy per ft and a digital readout for reliable, repeatable cuts across all woodworking projects
- Heavy-Duty Build: Crafted from durable steel and aluminum, this professional-grade table fence delivers long-lasting stability and is perfect for woodworking benches, rip cuts, and shop work tables
- Digital Readout: Features a backlit digital display showing readings in inches, fractions, or millimeters; constant memory preserves calibration even when powered off or removed from the bench rail
- Smooth Adjustment: Micro-adjust wheels and roller glide ensure fine-tuned, smooth fence movement - ideal for setting precise bevels, rip cuts, and repeat measurements on contractor or cabinet saws
- What’s Included: You get (1) Wixey Table Saw Fence System (WR750) - (1) Digital Readout Display – (1) 72” Fence Rail (ships in two parts) - (1) Drilling Jig & Bit - Mounting Hardware Included - Batteries (2×AAA, not included) with this digital fence tool
Rank #3
- PRECISION TABLE SAW RIP FENCE UPGRADE : Built from high-strength extruded aluminum, this table saw rip fence extension provides a stable, straight reference surface for cleaner and more consistent cuts. The rigid profile helps reduce flex and supports accurate alignment during repeated table saw operations
- 46" EXTENDED SUPPORT WITH SPACE-SAVING DESIGN : This 46" table saw fence extension kit with featherboards measures 47-1/4" overall and adds support when working with long boards or sheet goods. It functions as a table saw extension and outfeed support without requiring a bulky outfeed table
- VERSATILE 3-IN-1 MULTI-FUNCTION FENCE SYSTEM : Configure the fence for different cutting tasks: High Fence Mode supports tall panels and box work, Low Fence Mode 3/4" helps with controlled thin ripping, and L-Fence Mode supports edge jointing or template-guided cuts. It also works as a thin rip jig and table saw jig for added workshop flexibility
- 8 BUILT-IN T-SLOTS FOR CUSTOM JIG SETUPS: The fence body features eight integrated T-slots for mounting featherboards, stop blocks, hold-downs, and custom woodworking jigs. The included drop-in T-bolts can be inserted directly through the slot opening, allowing faster setup and adjustment without sliding hardware in from the ends of the track
- FITS MOST TABLE SAW FENCES WITH 1-1/4" OFFSET ALIGNMENT :Designed to clamp securely to most table saw rip fences without drilling or permanent modification. The 1-1/4" total thickness provides a clear offset reference
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
