If your refrigerator is making no ice or too little, start with the ice-maker setting, freezer conditions, water supply, filter and bin before resetting or replacing anything. These checks solve common interruptions without guessing at a failed part. Exact controls, temperatures and reset steps vary by refrigerator, so use the model number and owner’s manual for instructions specific to your appliance.
Check the simple causes first
Make sure the ice maker is on
Check the ice maker’s switch, control arm or user-interface setting. Some models let you turn ice production off independently of the refrigerator. If the appliance was recently installed, give it time to cool and begin producing: LG says a new installation can take up to two days to start making ice. That is LG guidance, not a guaranteed wait time for every brand or model.
Check freezer temperature and airflow
A freezer that is too warm, frequent door opening or blocked airflow can slow or stop ice production. Check the temperature setting recommended in your refrigerator’s manual and make sure stored food is not blocking vents. LG advises lowering the freezer temperature when needed; Whirlpool also recommends checking freezer conditions and airflow when troubleshooting a reset.
Check the water supply
Confirm the refrigerator’s water shutoff valve is open and the supply line is connected and not kinked. Inadequate flow can keep the ice maker from filling. If the water dispenser works but the ice maker does not, that observation alone does not identify which component has failed; continue through the checks below rather than assuming the valve or ice maker needs replacement.
#1 Best Overall
- Compatible Brands: 241798224 ice maker compatible with SOME Frigidaire Electrolux Kenmore Refrigerators etc.(Not Universal)
- Replaces Part Numbers: 241798231 ice maker replaces 241798224, 241798201, 5304456671, 241642501, 241642503A, 241798211, 241798231, 241642511, 241798209, 5303320545, 5303320545, 5304445222, 5304456669, PS10057209, AP6332951, 5304456672, 241798220, 75304445222, 75304456669, 75304456671, 75304456672, 4591526, AP6332951, PS12085911, 3206327 and 3206329, etc
- Solve Problems: 241798211 ice maker stopped making ice; it's a lit noisy; ice maker does not turn off
- Easy Installation: 241642511 ice maker is equipped with a new built-in wiring harness. Just unplug the power plug and install the new device. Install the ice maker by yourself and quickly get your refrigerator back to work
- Please Note: Before buying, please confirm whether it is suitable for your refrigerator model. If you can't find it, please let us know and we can check it for you
Inspect the filter
An old, clogged or incorrectly seated filter can restrict water flow. Check that the filter is installed and locked as the manual specifies. Whirlpool notes that an improperly installed filter can reduce or stop flow. LG recommends replacing its filter after six months of use; that is LG’s general guidance, not a universal interval, so follow the maintenance schedule for your model. After replacing a filter, follow the manual’s instructions for priming or flushing it.
Check the bin and accessible ice path
Make sure the ice bin is correctly positioned and not overfilled, and check for an obstruction in the accessible dispenser path or around the control arm. A frozen inlet tube is another possible cause identified by Whirlpool. Do not remove covers, disassemble components or handle electrical parts while the refrigerator is powered.
Rank #2
- Compatible with major brands including Kenmore, Whirlpool, Admiral, Amana, Crosley, Magic Chef, Maytag, Sub-Zero, Roper, KitchenAid, Jenn-Air, etc. Fits models: 36538(P1121904WL), 7GJ5FSAXVY00, 7MI2569VEM10, ABB2527DEB14, ABB2527DEW14, ABC2037DEB14, ABC2037DEW14, ABC2037DPS, ABC2037DTB, ABC2037DTS, ABC2037DTS14, ABC2037DTW, ABD2233DEB, ABD2233DEQ, ABD2233DES
- Manufactured to strict original equipment specifications with performance meeting OEM standards. Complete set includes head cover, bail arm and water trough (wiring harness not included). Designed to replace 120-volt 8-cube modular ice maker
- Constructed with sturdy thermoplastic housing and metal components featuring heat, wear, and moisture resistance, this unit effectively resolves various malfunctions including water leakage, abnormal noise, no ice production, and abnormal ice cubes while delivering reliable cooling performance and ensuring consistent ice production
- Always disconnect power before installation. Remove the old unit and transfer all hardware to the new ice maker. Ensure the unit is level and securely connected to the wiring harness, then engage the lift arm to activate the mechanism. Wear work gloves throughout the entire process and avoid damaging the water fill tube
- Due to the extensive range of compatible models, only the most common ones are listed. If your model is not shown or if you encounter any issues during installation or use, feel free to contact us. We provide professional technical support to ensure all your concerns are properly resolved
Should you reset the ice maker?
A reset may clear a temporary interruption, but the procedure is model-dependent. Use the reset instructions in the owner’s manual or manufacturer support page for your exact refrigerator. Whirlpool describes a reset button on some ice makers and a one-minute refrigerator power cycle for applicable models; neither procedure applies to every refrigerator. If you use a power cycle, follow the model’s instructions for safely disconnecting and restoring power.
If ice production does not resume after the specified reset, return to the underlying checks: temperature and airflow, water supply, filter installation and bin obstruction. A reset is not evidence that a faulty component has been repaired.
Rank #3
- IT FROM XUQCAH MATERIAL AND FOIMOJSK PARTMENT AND Thurder LOVER
When a replacement part or technician may be needed
Possible hardware causes include a water inlet valve or the ice maker assembly, but similar symptoms can also result from temperature, flow or filter problems. Frigidaire Appliance Parts lists those components among potential causes and places assembly replacement later in its model-specific troubleshooting sequence. That guidance is not a universal service procedure.
Before buying a filter, water line, inlet valve or ice maker assembly, find the refrigerator’s exact model number—often on a label inside the fresh-food compartment or around the door opening—and verify compatibility using the manufacturer’s parts lookup. Do not choose a part based only on the brand or on how it looks. The available guidance does not establish a universal part number, price or repair time.
Rank #4
- UNIVERSAL ICE MAKER REPLACEMENT - This Supco modular ice maker unit is an excellent replacement for units 797991 (Whirlpool), 625601 (Whirlpool), 4210317 (Whirlpool), and 4317943 (Whirlpool)
- HIGHEST QUALITY PARTS - The RIM943 meets or exceeds OEM specifications
- WIDESPREAD USE - Supco modular ice maker kit is designed to work with existing wiring and plumbing
- HIGH COMPATIBILITY - Made for use with Kenmore, Whirlpool, KitchenAid, Roper, and Sub-Zero brands. Will replace most modular ice makers if using old wiring harness
Use a qualified appliance technician if diagnosis requires electrical testing, wiring work or sealed-system service, or if you are not comfortable carrying out the model’s repair procedure. Follow the appliance manual and manufacturer safety guidance; do not work on electrical components with the refrigerator powered.
Quick Recap
Best Value
- UNIVERSAL ICE MAKER - This Supco ice maker unit is a direct replacement for most of the 120V modular style ice makers.
- HIGHEST QUALITY PARTS - The RIM900 meets or exceeds OEM specifications.
- EASY INSTALLATION - Ice maker is designed to use the existing ice maker wire harness. Wire harness NOT included.
- WIDESPREAD USE - Supco modular ice maker replaces hundreds of different modular ice makers on tens of thousands of refrigerators.
- HIGH COMPATIBILITY - Made for use with Kenmore, Whirlpool, Admiral, Amana, Crosley, Magic Chef, Maytag, SubZero, and many more brands.
A quick troubleshooting order
- Confirm the ice maker is enabled and, after a new installation, allow for the model’s initial cooling and ice-making period.
- Check that freezer temperature follows the manual’s guidance and that vents are not blocked.
- Confirm the water valve is open and the supply line is connected and unkinked.
- Check the filter’s condition and seating; follow the model’s replacement and priming instructions.
- Inspect the bin, control arm and accessible dispenser path for obstruction.
- Use only the reset procedure specified for the exact refrigerator model.
- If the problem remains, identify the model and seek model-specific diagnosis before ordering parts.
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
